LumiDesk Forum

Hello Mark,
You can make a backup of your programm and then load it in the new Version. Than you get all your saved colors.

Kind regards
Chris

Hello,

I have a problem with the palettes.
You cannot rename the palettes.
The only possibilities are (1), (1)(1), (1)(1)(1) and so on........
Any ideas?

Regards
Chris

I have problems too.
Sometimes when I switch from live mode to desktop mode i cannot control some fixtures.
Then I have to restart lumidesk.

Hello, i noticed something in the Auto Fade function. I have one cue with sequences for each color. If I change the sequences from sequence 1 to a higer one like 2, 3, 4, there is a smoothly fade from one color to the other. But in the other direction from a higer sequence to a lower sequence there ...

Hello missbethany, i had the same problem with my LED-Pars. The fixtures must be stored in the ScanLibrary of your new version under the same Name and in the same folder as in the older version. In my case, a clerical error of the old version was corrected, and lumidesk could not find the fixture. M...

Hi, I tried it and it works. But I still do not understand. The solution with the red channel works better. But when you select chaser or random then you cannot change the brightness. But I still have a few questions. I want to patch two sunstripes. That means two times a matrix of 2x10? Is that rig...

Thanks LDK34.

Julien told me the second solution too.
I will try both tomorrow.
Hope it works

kind regards
Chris

Hello,

I sent it to [email protected].
Thank You.

regards
Chris

Hello, i have one of the Showtec Sunstrip Active MK II. This fixture has 10 lamps with dimmer. Now I want to create a chase-effect with all 10 lamps, but in the effect manager I can only see seven dimmers. Is seven dimmers the maximum to control with the effect manager? How can I solve this problem?...

It was with connected Interface.
With the preversion of the software and hardware (1.19) it runs normal.

ok
this sounds not very good.
Yes, when I close lumidesk and start it the problem is solved for some time.

Have you the problem with channel 102 and 104, too? Both are 255 and I don't know why?

Hello, I have a problem with the latest update oft the lumidesk software and hardware. After a while the Desktop Mode crashes so I see no further reaction of the lights. Live Mode still works. And sometimes channel 102 and 104 have full DMX level. Even if I don't use them. The lights of the interfac...

Hello Julien,
I would say it's ok in general settings.
Thank you.

Kind regards
Chris

OK I send you an excample.

Yes I think so.
But I have 8 LED-Pars and I pragrammed a sequence with a few scences.
And in every scence the Pars have various colors which change i the next scence.
That does not work with copy an paste or, because I have more pars with various colors in the same scence.

Hello, I have six LED-Pars and I have programmed a few sequences. When programming I noticed it is complicated to set the same color again. You have to remember the numbers of green, blue and red. Now my question Is it possible to create a few buttons where you can store your own colors. Or is there...

Hello,

The problem was solved. The interface was to old.
I have updated to Lumidesk Ultimate.

Thanks
Chris

Hello, I wanted to update my Lumidesk-Live Interface to Firmware SIUD8C 1.08. When I click "write Firmware" the green LED flashs for a few seconds and then it turns off and the interface is disconnected. There is the message "No compatible dmx-hardware is connected". Has anybody ...

I agree, this would be usefull.
For example to use the whole number pad (+ - ,).

thanks
Chris

Yes it works with the sequence.
But it doesn't work with the scences. There are no scences in Live mode only sequences!!!

Yes, with the sequences it's ok.
But what is if I want to see the last scences.
Here it always starts by scence 1, or???

Hello, When you put the Play Button in the Sequence window the programm plays all Scences starting from Scence 1. Now my question: Is ist possible to create a second Play Button or an choice button to select two different play modes. One to start at the beginning (Scence 1) and the other mode (butto...

Hello, When you put the Play Button in the Sequence window the programm plays all Scences starting from Scence 1. Now my question: Is ist possible to create a second Play Button or an choice button to select two different play modes. One to start at the beginning (Scence 1) and the other mode (butto...

The LED_DMX 2 is blinking.
The LED_DMX 1 is not blinking it;s illuminated

Thanks
Chris

Hello Julien,

Thanks for the quick answer.

I think the version is SIUDI8 V1.1 Lumidesk Live.
Before I updated the firmware only the LED_DMX2 was illuminated;
Now LED_DMX1 and LED_DMX2 are both illuminated.

Thanks

Hello, I'm Chris from Germany and a few month ago, I bought the Lumidesk Live Interface. I downloaded the Lumidesk version of 2011/01/4 and updated the firmware to 1.07 It's my first DMX software and I'm very glad that I have decided on Lumidesk. Now I have some questions about the software and the ...